1 General
5
1.1 Explanations Of The Symbols
5
1.2 Information Regarding The Manual
5
1.3 Liability And Warranty
6
1.4 Copyright
6
1.6 Spare Parts
6
1.7 Disposal
7
2 Safety
8
2.1 Intended Use
8
2.2 Manual Contents
8
2.3 Making Changes And Modifications To The Machine
8
2.4 Responsibilities Of The Operator
9
2.5 What Is Required Of The Personnel
9
2.6 Work Safety
9
2.7 Personal Safety
10
2.8 Hazards Arising From The Machine
10
2.9 Other Risks
10
3 Declaration Of Conformity
11
4 Technical Data
12
4.1 Dimensions And Weight
12
4.2 Operation And Storage Conditions
12
4.3 Electrical Connection
12
4.4 Noise Emissions
13
4.5 Dust Extraction
14
5. Setting Up The Machine
15
5.1 Overview
15
5.2 Data Plate
16
6 Setup And Installation
17
6.1 Safety Instructions
17
6.2 Positioning
17
6.2.1 Safety Instructions
18
6.2.2 Setting Up The Work Table
18
7 Operation
19
7.1 Safety Instructions
19
7.2 Switching On The Machine
20
7.3 Authorised Work Techniques
20
7.4 Authorised Work Techniques
21
7.4.1 Positioning The 90° End Stop On The Work Table
21
7.4.2 Parallel Cutting Fence
21
7.4.3 Saw Blade Replacement/Tension
22
7.4.4 Longitudinal Cut Along The Marked Line
22
7.4.5 Cutting Round Work-Pieces In The Transverse Direction
23
7.4.6 Longitudinal Cut Of Narrow Or Thin Work-Pieces With The Guide Fence
23
7.4.7 Cutting Work-Pieces On The Upright Edge
23
7.4.8 Angular Cuts
24
7.4.9 Circular Cuts
24
7.4.10 Diagonal Cross Cuts Of Rectangular Work-Pieces
24
7.5 Applications
25
7.5.1 Blade Selection And Maintenance
25
7.5.2 Adjusting The Saw Blade Guide
26
7.5.2.1 Upper Blade Guide
26
7.5.2.2 Lower Blade Guide
26
8. Maintenance
27
8.1 Safety Instructions
27
8.2 Cleaning And Lubrication
27
8.3 Drive Belts
28
8.3.1 Adjusting The Belt Tension
28
9 Faults
29
9.1 Safety Instructions
29
9.2 What To Do In Case Of A Fault
29
9.3 What To Do After Rectifying The Fault
29
9.4 Faults, Causes And Repairs
30
10 Circuit Diagram
32
10.1 Safety Instructions
32
11 Spare Parts
34
11.1 Machine Base-Frame
34
11.2 Machine Table
35
11.3 Height Adjustable Protection Device
36
11.4 Upper Wheel
37
11.5 Lower Wheel
38
11.6 Safety Equipment
39
12 Index
40
Discussie
Laat een opmerking achter of stel een vraag
Hallo, ik heb een Hammer N4400 lintzaag en ik heb problemen met het spannen van het zaagblad. Het blad lijkt steeds te slppen tijdens het zagen van dikker hout. Hoe weet ik of de spanning goed is ingesteld en wat is de juiste procedure daarvoor?
Dat herken ik wel, dat had ik in het begin ook. Bij de N4400 moet je het zaagblad spannen via de spanningsknop bovenaan het bovenste wiel. Een goede vuistregel is dat het blad ongeveer een centimeter zijdelings moet kunnen buigen als je er met je vinger tegenaan drukt. Zorg ook dat de bladgeleiders goed zijn afgesteld, want slechte geleiding is vaak de echte oorzaak van slippen. Kijk even in het handboek bij het onderdeel over het verwisselen en spannen van het blad, daar staat de exacte procedure netjes uitgelegd.
Doe mee aan de discussie
Stel een vraag over de handleiding of voeg een nuttig antwoord toe voor andere gebruikers.