GE DBVH520EJ2WW Wasdror Wasdrogers Handleiding

Oorzaak: Lint filter is full

Clean lint filter before every load.

Oorzaak: Blown fuses or tripped circuit breaker

Replace fuses or reset circuit breakers. Since most dryers use 2 fuses/breakers, make sure both are operating.

Oorzaak: Overloading/combining loads

Do not put more than one washer load in the dryer at a time.

Oorzaak: Underloading

If you are drying only one or two items, add a few items to ensure proper tumbling.

Oorzaak: Load consists of a mixture of heavy and light fabrics

When combining heavy and light fabrics in a load, choose MORE DRY.

Oorzaak: Exhaust system is blocked

Inspect and clean exhaust system.

Oorzaak: Controls accidentally put in service mode

Press STOP.

Oorzaak: Controls accidentally put in lock mode

Hold the LOCK button for 3 seconds to unlock the dryer.

Oorzaak: Controls performed an incorrect operation

Reset the in-house breaker.

Oorzaak: Control panel is asleep

This is normal. Press POWER to activate the control panel.

Oorzaak: Dryer is unplugged

Make sure the dryer plug is pushed completely into the outlet.

Oorzaak: Fuse is blown/circuit breaker is tripped

Check the building's fuse/circuit breaker box and replace fuse or reset breaker. NOTE: Electric dryers use two fuses or breakers.

Oorzaak: Dryer was accidentally paused when starting

If the light on the DELAY START pad is flashing, the dryer is paused. Press START to restart the countdown.

Oorzaak: Dryer is continuously monitoring the amount of moisture in the clothes

This is normal. When the dryer senses a low level of moisture in the load, the dryer will display the dry time remaining.

Oorzaak: The estimated time may change when a smaller load than usual is drying

This is normal.

Oorzaak: The DRYNESS LEVEL, TEMP or OPTION that you are trying to select is incompatible with the chosen dry cycle

This is normal.

Oorzaak: The EXTEND TUMBLE option was chosen

This is normal. During extended tumbling, the time remaining is not displayed. The extended tumbling option lasts approximately 20 minutes.

Oorzaak: POWER button was activated

Press START to begin a dry cycle and the message will disappear.

Oorzaak: Fuse is blown/circuit breaker is tripped

Check the building's fuse/circuit breaker box and replace both fuses or reset both breakers. Your dryer may tumble if only one fuse is blown or one breaker tripped.

Oorzaak: Gas service is off

Make sure gas shutoff at dryer and main shutoff are fully open.

Oorzaak: LP gas supply tank is empty or there has been a utility service interruption of natural gas

Refill or replace tank. Dryer should heat when utility service is restored.

Oorzaak: Type of heat

Drying time will vary according to the type of heat used. If you recently changed from an electric to a gas (natural or LP) dryer, or vice versa, the drying time could be different.

Oorzaak: Type of load and drying conditions

The load size, types of fabric, wetness of clothes and the length and condition of the exhaust system will affect drying times.

Oorzaak: Heaters behind the drum

This is normal. Under certain drying conditions and room ambient lighting, the glow of the heaters may be visible at the rear of the drum.

Oorzaak: The door was opened mid-cycle. The load was then removed from the dryer and a new load put in without selecting a new cycle

A dry cycle must be reselected each time a new load is put in.

Oorzaak: Small load

When drying 3 items or less, choose SPEED DRY or TIMED DRY.

Oorzaak: Load was already dry except for collars and waistbands

Choose SPEED DRY or TIMED DRY to dry damp collars and waistbands. In the future, when drying a load with collars and waistbands, choose MORE DRY.

Oorzaak: Dryer is not level

Move dryer to an even floor space or adjust leveling legs as necessary until even.

Oorzaak: Overdrying

Select a shorter drying time. Remove items while they still hold a slight amount of moisture.