LG DLEX3550W Wasdroger Handleiding

Oorzaak: Clean and dirty clothes being dried together

Make sure to use your dryer to dry only clean items, because dirty items can soil clean clothes placed in the same or subsequent loads

Oorzaak: Lint filter not cleaned properly

Make sure the lint filter is cleaned before every load. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle

Oorzaak: Laundry not sorted properly

Some fabrics are lint producers (i.e., a fuzzy white cotton towel) and should be dried separately from clothes that are lint trappers (i.e., a pair of black linen pants)

Oorzaak: Dryer is overloaded

Divide larger loads into smaller loads for drying

Oorzaak: Tissue, paper, etc., left in pockets

Check pockets thoroughly before washing and drying clothes

Oorzaak: Fabric softener not used or used incorrectly

Use a fabric softener to reduce static electricity correctly. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer

Oorzaak: Clothes dried too long (overdried)

Overdrying a load of laundry can cause a buildup of static electricity. Adjust settings and use a shorter drying time, or use SENSOR DRY cycles

Oorzaak: Drying synthetics, permanent press, or synthetic blends

These materials can cause static buildup. Try using a fabric softener

Oorzaak: Heat settings, load size, or dampness of clothing is not consistent

The drying time for a load will vary depending on the heat setting, the type of heat used, the size of the load, the type of fabrics, the wetness of the clothes, and the condition of the exhaust ducts and lint filter

Oorzaak: Load is not properly sorted

Separate heavy items from lightweight items. Larger and heavier items take longer to dry

Oorzaak: Large load of heavy fabrics

Heavy fabrics take longer to dry because they tend to retain more moisture. To help reduce and maintain more consistent drying times, separate these items into smaller loads of a consistent size

Oorzaak: Dryer controls are not set properly

Use the appropriate control settings for the type of load you are drying

Oorzaak: Lint filter needs to be cleaned

Make sure the lint filter is cleaned before every load. With some loads that produce high amounts of lint, it may be necessary to clean the filter during the cycle

Oorzaak: Exhaust ducts blocked, dirty, or duct run is too long

Confirm that the exhaust ductwork is properly configured and free of debris, lint, and obstructions. Make sure that outside wall dampers can open properly and are not blocked, jammed, or damaged

Oorzaak: Dryer is overloaded

Divide larger loads into smaller loads for drying

Oorzaak: Dryer is underloaded

If you are drying a very small load, add a few extra items to ensure proper tumbling action

Oorzaak: Clothes dried too long (overdried)

Overdrying a load of laundry can lead to wrinkled clothes. Try a shorter drying time, and remove items while they still retain a slight amount of moisture

Oorzaak: Clothes left in dryer too long after cycle ends

Remove items from the dryer immediately at the end of the cycle. Use the WRINKLE CARE option to continue tumbling clothes at the end of the cycle, for up to 3 hours

Oorzaak: Garment care instructions are not being followed

To avoid shrinkage, please carefully follow the fabric care instructions for your garment, because some fabrics will naturally shrink when washed. Other fabrics can be washed but will shrink when dried in a dryer. Use a low or no heat setting

Oorzaak: Water supply error

Check steam feeder drawer: Make sure steam feeder is filled with water to MAX line. Make sure steam feeder is seated properly and drawer is fully closed. Turn the dryer off then restart the Steam cycle. Do not use distilled water; the water level sensor in steam generator will not work

Oorzaak: Pump not working

Unplug dryer and call for service

Oorzaak: This is normal

This is steam condensation. The dripping water will stop after a short time

Oorzaak: Water level error

Unplug dryer and call for service

Oorzaak: Too many or too different types of garments in dryer

Small loads of 1 to 5 items work best. Load fewer garments. Load similar-type garments

Oorzaak: The function of this cycle is to remove wrinkles from fabric

Use an iron to make creases

Oorzaak: This is normal

Depends on individual moisture level in skin

Oorzaak: Correct drying options not selected

Select load weight manually before starting REDUCE STATIC option

Oorzaak: Number of garments or load size not properly selected

Select the correct number or garments or load size before starting the cycle