Contents 7.4 Yearly Maintenance
25
7.5 Cleaning The Product
26
1 Safety .................................................................... 3 7.6 Draining The Product
26
1.1 Action-Related Warnings ......................................... 3 7.7 Checking The Product's Status Codes
27
1.2 Required Personnel Qualifications ......................... 3 7.8 Checking The Electrical Installation
27
1.3 General Safety Information .................................... 3 7.9 Start-Up Following Maintenance
27
1.4 Regulations (Directives, Laws, Standards) .............. 4 8 Troubleshooting
27
1.5 Ce Label ................................................................. 4 8.1 Troubleshooting
27
1.6 Approvals............................................................... 5 8.2 Fault Codes
27
1.7 Local Regulations.................................................... 5 8.3 Carrying Out The Actuator Test
27
1.8 Regulations............................................................ 5 9 Decommissioning
28
1.9 Other Regulations ................................................... 5 9.1 Temporary Decommissioning
28
1.10 Intended Use.......................................................... 6 9.2 Permanently Decommissioning
28
2 Notes On The Documentation .............................. 7 10 Vaillant Customer Service
28
2.1 Observing Other Applicable Documents ................. 7 10.1 Customer Service
28
2.2 Storing Documents................................................. 7 11 Disposal
28
2.3 Applicability Of The Instructions .............................. 7 11.1 Recycling And Disposal
28
3 System Overview.................................................. 7 11.2 Arranging Disposal Of Coolant
28
3.1 Safety Devices ....................................................... 7 Appendix
29
3.2 Design Of The Heat Pump System........................... 7 A Overview Of Accessories
29
3.3 Functionality........................................................... 7 B System Diagrams
30
3.5 System Diagram (Vwl 85/2 A 230 V, Vwl B.2 System Diagram 8 F
32
115/2 A 230 V, Vwl 155/2 A 230 V)
8
B.3 System Diagram 10 B
34
4 Overview Of The Equipment................................. 9 B.4 System Diagram 12 A
36
4.1 Type Designation And Serial Number
9
C Wiring Diagrams
37
4.2 Information On The Identification Plate
9
C.1 Wiring Diagram 8 E
37
5 Assembly And Installation .................................. 9 C.2 Wiring Diagram 8 F
38
5.1 Preparing For Fitting And Installation ....................... 9 C.3 Wiring Diagram 10 B
39
5.2 Carrying Out The Installation
14
C.4 Wiring Diagram 12 A
40
5.3 Hydraulics Installation
14
D Heat Pump Schematic
41
5.5 Connection Diagrams........................................... 19 230 V)
41
230 V)
42
6.1 Run The Start-Up
21
6.2 Heat Pump Operating Concept
21
230 V)
43
6.3 Running Through The Installation Assistant
21
230 V)
44
Codes)
21
E Heat Pump Setting Parameters
44
6.5 Calling Up Statistics
21
F Technical Data
45
6.6 Filling The Heating Circuit
21
G Overview Of Fault Codes
48
6.7 Preparing The Heating Water
22
Index
51
6.8 Filling The Heating Installation
23
6.9 Activating The Heat Pump
23
6.10 Checking The Product's Operation
23
6.11 Operating Noises
23
6.12 Adjusting The Heating Circuit
23
6.13 Installing The Side Cladding
25
6.14 Instructing The Operator
25
7 Maintenance
25
7.1 Observing Maintenance Intervals
25
7.2 Preparing For Maintenance
25
Work
25
Discussie
Laat een opmerking achter of stel een vraag
Ik heb een Vaillant aroTHERM VWL 55-2 en bij het vullen van het verwarmingscircuit krijg ik steeds lucht in het systeem. De druk zakt na een paar dagen weer terug naar onder 1 bar. Heeft iemand tips hoe ik dit goed kan ontluchten? Is er een specifieke volgorde die ik moet aanhouden?
Dit herken ik wel, had er zelf ook last van. Bij de aroTHERM VWL 55-2 is het belangrijk dat je tijdens het vullen alle ontluchters open zet en het systeem langzaam vult zodat de lucht goed weg kan. Zorg dat de druk op minimaal 1,5 bar komt. In het installatiehandboek staat een specifieke procedure voor het vullen beschreven, dat raad ik je echt aan even door te lezen. Na het vullen even een testvlucht draaien helpt ook om resterende lucht eruit te krijgen.
Doe mee aan de discussie
Stel een vraag over de handleiding of voeg een nuttig antwoord toe voor andere gebruikers.