Gebruik de reader hieronder om de Gorenje GV65160XXLCUS Vaatwasser handleiding te lezen. U kunt de handleidingen direct op de pagina doorbladeren en de functies van onze reader gebruiken om alle belangrijke informatie over de installatie, bediening en het onderhoud van deze Gorenje Vaatwasser te vinden.
Handleiding
Volledig schermFoutcodes
Hieronder vindt u de error codes voor de Gorenje GV65160XXLCUS.
Overfilling
Clear the drain pump. See the chapter Care and maintenance instructions. If the problem persists, call the Customer Care Center.
Water outlet fault
See 'Water remains in the dishwasher above the filters' in the table 'Problem' below. If the problem persists, call the Customer Care Center.
Water inlet fault
Check that the water supply valve is on. If the problem persists, call the Customer Care Center.
Inlet valve leakage
Turn off the water supply valve and call the Customer Care Center.
Water level fault
Clean the coarse and fine filters. If the problem persists, call the Customer Care Center.
Overfilling
Turn off the water supply valve and call the Customer Care Center.
Circulation fault
Call the Customer Care Center.
Probleemoplossing
Praktische tips om de meest voorkomende problemen met Gorenje GV65160XXLCUS op te lossen.
Oorzaak: Buttons pressed too soon after opening the door, buttons are dirty, or door is not closed
Wait a moment then try again. Clean buttons with a dry or slightly damp cloth. Open the door - buttons only react when the door is open.
Oorzaak: Baskets are not correctly positioned or dishes are blocking the baskets
Check that the baskets are correctly positioned horizontally. Ensure dishes are not blocking the baskets from sliding properly into place.
Oorzaak: Door not closed properly, fuse/circuit breaker tripped, plug not inserted, water supply valve off, or Delayed start option selected
Close the door within four seconds. Check fuse/circuit breaker. Check plug connection. Check water supply valve. Press and hold the main power switch to cancel Delayed start option if selected.
Oorzaak: Drain pump issue or Delayed start option selected
Turn off the water supply valve, pull out the plug and call the Customer Care Center. Check that the Delayed start option has not been selected.
Oorzaak: Spray arms do not rotate, spray arm holes or bearings blocked, unsuitable program, incorrect detergent dosage, old detergent, dishes loaded incorrectly, or filters not fitted correctly
Remove and clean the arms. Ensure dishes are not blocking spray arms. Choose a longer program. Dose detergent according to water hardness. Avoid old detergent. Load dishes correctly without covering them with large bowls or lids. Check that filter handle is locked in stop position.
Oorzaak: Food residue such as mustard, mayonnaise, lemon, vinegar, salt left too long. Contact between different metals.
Rinse off these types of food if not starting the dishwasher immediately. Use the Rinse program. Separate dishes made from different metals such as silver, stainless steel, and aluminum.
Oorzaak: Water softener leaking salt, incorrect water softener setting, incorrect rinse aid dosage, empty salt compartment, or 3-in-1 detergent setting activated
Check that the salt compartment lid is properly tightened. Verify water softener and rinse aid settings. Top up with salt. Deactivate the TAB setting and top up with salt and rinse aid.
Oorzaak: Rinse aid dosage setting too high
Reduce the amount of rinse aid. If you have very soft water, you may want to dilute the rinse aid 50:50 with water.
Oorzaak: Filters are blocked, filters not fitted correctly, debris in drain pump, drain pump stop missing, kinked drain hose, or blocked drain hose
Clean the coarse and fine filters. Check that filter handle is locked in stop position. Clean the drain pump. Check that the colored stop on the right in the bottom drain is in place. Ensure the hose is free from kinks and sharp bends. Loosen the drain hose and check for clogged debris.
Oorzaak: Dirt around seals and in corners, or low temperature programs selected for prolonged period
Clean with dish brush and low foaming cleaner. Run a program with higher temperature about once a month.
Oorzaak: Program's drying cycle may be insufficient, dishwasher not fully loaded, rinse aid needs topping up or dosage set too low, or 3-in-1 detergent setting activated
Activate the Extra dry option. Fully load the dishwasher. Top up with rinse aid or increase the rinse aid dosage. Deactivate the TAB setting and top up with salt and rinse aid. Open the door a little once the program has finished.
Oorzaak: Dishes not correctly placed or spray arms not rotating
Check that the dishes are placed securely. Spin the spray arms to make sure they can rotate.
Oorzaak: Dishwasher door has been opened while a program is in progress
If you want the dishwashing program to continue, press the Program selector and close the door within five seconds. If you want to cancel the program, press and hold the main power switch until the display turns off.
Veelgestelde Vragen
De meest gestelde vragen over de Gorenje GV65160XXLCUS.
Hulp
Heb je vragen over de Vaatwasser GV65160XXLCUS van Gorenje? Stel ze direct aan onze expert! Je krijgt informatie, praktische tips en oplossingen op maat in slechts enkele seconden.
Gerelateerde handleidingen
Hieronder vindt u handleidingen voor Vaatwasser die vergelijkbaar zijn met GV65160XXLCUS. Probeer ook alle Gorenje Vaatwasser handleidingen te bekijken
Discussie
Laat een opmerking achter of stel een vraag
Doe mee aan de discussie
Stel een vraag over de handleiding of voeg een nuttig antwoord toe voor andere gebruikers.