Flymo UltraLife 600 Robotmaaier Handleiding

Oorzaak: Boundary wire configuration issues or too near edge or incorrect direction around island or interference from metal objects or interference from other product installation

Ensure boundary wire is connected and installed correctly. Move boundary wire away from metal objects. Refer to installation instructions

Oorzaak: Cannot find charging station or battery at end of life cycle or damaged antenna or corroded charging plates

Change position of guide wire. Replace battery if at end of life. Check charging station antenna. Clean charging plates and contact plates

Oorzaak: Product caught in something or steep slope or guide wire not placed diagonally on slope or wet grass

Free product and correct cause. Wait until lawn is dry. Ensure guide wire is installed diagonally across slope

Oorzaak: Grass or other object around drive wheel

Remove grass or object from drive wheel

Oorzaak: Front wheels blocked

Free product and correct cause of problem

Oorzaak: Poor contact between charging plates or object blocking station or tilted charging station or guide wire not installed correctly

Ensure charging plates are connected. Remove blocking object. Level charging station. Install guide wire correctly

Oorzaak: Object prevents product from moving out

Remove the object

Oorzaak: Product in incorrect position, tilting too much or upside down

Put product in correct position

Oorzaak: Lift sensor enabled because product lifted

Ensure product body can move freely. Remove or create island around objects causing chassis lift

Oorzaak: Grass or other object around drive wheel

Clean wheels and around wheels

Oorzaak: Temporary electronic or firmware related problem

Restart the product. Contact Flymo service if problem persists

Oorzaak: Corrosion or dirt on charging plates or temporary electronic problem

Restart product. Clean charging plates and contact plates

Oorzaak: Temporary battery or firmware problem or incorrect battery type

Restart product. Use original batteries recommended by manufacturer. Contact Flymo service if persists

Oorzaak: Battery temperature too high or too low to start operation

Wait for temperature to return to operating limits. Charging/mowing will start automatically

Oorzaak: Incorrect or damaged power supply unit

Restart product. Replace power supply unit if necessary

Oorzaak: Power supply not connected or damaged or boundary wire not connected or damaged or product not in charging station in ECO mode or boundary wire configuration issues or interference from metal objects or product too far from boundary wire

Check power supply connection. Replace damaged cables. Connect boundary wire correctly. Put product in charging station and make new loop signal. Move boundary wire away from metal objects. Ensure work area is maximum 15 m / 50 ft from boundary wire

Oorzaak: Product tilted more than maximum angle

Move product to level area

Oorzaak: Guide wire not connected to charging station or damaged or not connected to boundary loop

Connect guide wire to charging station and boundary loop. Replace damaged guide wire sections

Oorzaak: Loop signal not changed because of error

Make new loop signal multiple times. Contact Flymo service if problem persists

Oorzaak: Product stopped due to steep slope

Change boundary wire installation to exclude steep part of work area

Oorzaak: Vibrations detected in blade disc

Examine blades and screws for damage or wear. Ensure all blades are correctly installed with only one blade per position

Oorzaak: Incorrect or damaged power supply unit or power failure or no contact between charging plates

Examine and replace power supply unit if necessary. Find and correct power failure cause. Ensure charging plates are clean and in contact

Oorzaak: No guide wire or boundary wire in work area or stay-out zone blocking path

Edit or make new installation including guide or boundary wire. Remove or edit stay-out zone

Oorzaak: Obstacle blocks path to destination

Remove blocking obstacle

Oorzaak: Battery state of health is low

Replace battery. Contact authorized service technician

Oorzaak: Battery state of health critically low

Replace battery. Contact authorized service technician

Oorzaak: Firmware in product is invalid

Put product in charging station and update firmware via FOTA. Contact authorized service technician if problem remains

Oorzaak: ZoneProtect accessory battery low or temperature too high

Charge ZoneProtect accessory before starting product. Move product to area with sun protection to cool accessory

Oorzaak: Edge cutting system blocked by grass or other objects

Examine edge cutting system and remove grass or other objects

Oorzaak: Vibrations detected in edge blade disc

Examine blades and screws for damage or wear. Ensure all blades are correctly installed with only one blade per position