1 About These Instructions
5
1.1 Scope Of The Instructions
5
1.2 Representation Conventions – Symbols And Characters
5
1.3 Other Documents
6
1.4 Liability
7
1.4.1 Transport
7
1.4.2 Proper Use
7
2 Safety Instructions
9
2.1 Basic Safety Instructions
9
2.2 Signal Words And Symbols Used In Warnings
11
3 Working Basis
15
3.1 Sequence Of Settings
15
3.2 Laying The Cables
15
3.3 Removing Covers
16
3.3.1 Tilting And Re-Erecting The Machine Head
16
3.3.2 Removing And Fitting The Head Cover
17
3.3.3 Removing And Fitting The Arm Cover
18
3.3.4 Removing And Fitting The Covers On The Base Plate
19
3.3.5 Removing And Inserting The Throat Plate
20
3.3.6 Removing And Inserting The Top Feed Foot And Sewing Foot
21
3.3.7 Removing And Installing The Feeds
22
3.3.8 Removing And Fitting The Oil Pan
23
3.3.9 Removing And Fitting The Upper Belt Guard
24
3.3.10 Removing And Fitting The Lower Belt Guard
25
3.4 Removing Disruptive Components
26
3.4.1 Removing And Installing The Thread Cutter
26
3.4.2 Removing And Installing The Needle Protection
28
3.4.3 Removing And Installing The Looper And Looper Mounting
29
3.5 Flat Surfaces On Shafts
30
3.6 Locking The Machine
30
4 Gauge And Key Set
33
5 Setting The Adjusting Disk To The Arm Shaft Crank
36
6 Setting The Holding Position Of The Machine
38
7 Setting The Lower Toothed Belt Wheel
39
8 Setting The Sewing Foot
40
8.1 Setting The Sewing Foot Stroke
40
8.2 Setting The Speed Of The Sewing Foot Lifting
41
9 Setting The Looper
42
9.1 Setting The Rocker Bolt And The Left Lower Shaft Bearing
42
9.1.1 Draining And Filling The Oil In The Looper Drive Housing
43
9.1.2 Removing And Fitting The Looper Drive Housing
44
9.1.3 Setting The Left Lower Shaft Bearing
45
9.1.4 Setting The Rocker Bolt
46
9.2 Setting The Looper Drive Housing
48
9.3 Setting The Needle Evasive Movement (Ellipsis Width)
49
9.3.1 Setting The Needle Evasive Movement
50
9.3.2 Resetting The Needle Protection
52
9.4 Setting The Symmetry Of The Looper Motion
52
9.5 Setting The Looper In The Looper Mounting
54
9.6 Setting The Looper And Needle Bar Height
56
9.6.1 Setting The Looping Stroke Position And Looper Gauge
57
9.6.2 Setting The Needle Bar Height
58
9.7 Setting The Retention Spring On The Looper
59
9.8 Setting The Stitch Length-Controlled Thread Take-Up
61
10 Setting The Needle Protection
63
11 Differential Top And Bottom Feed
65
11.1 Setting The Feed Motion Of The Feeds
65
11.2 Setting The Stroke Motion Of The Feed
66
11.3 Setting The Angle Of Incline And The Height Of The Feeds
67
11.4 Basic Setting Of Bottom Feed Guides
68
12 Foot Top Feed
70
12.1 Setting The Stroke Height Of The Top Feed
70
12.2 Setting The Time Of The Stroke Motion
72
12.3 Setting The Time Of The Feed Motion
73
12.4 Setting The Position Of The Top Feed Foot
74
12.5 Basic Setting Of Top Feed Guides
75
13 Setting The Thread Take-Up Disk
77
14 Setting The Thread Cutter
79
15 Setting The Thread Guide On The Machine Arm
84
16 Setting The Tape Feed (Only 610)
85
17 Programming
89
17.1 Basic Settings For New Programs
89
17.2 Basic Settings, Machine
89
17.3 Language Selection
91
17.4 User Settings
92
17.5 Usb Settings
92
17.6 Machine Calibration
92
17.7 Reset Settings
93
17.8 Test Input/Output
93
17.9 Calibrating Electrical Thread Tension
93
17.10 Synchronizing The Feeds
95
17.10.1Calibrating The Main Feed
95
17.10.2Calibrating The Differential Bottom Feed
96
17.10.3Calibrating The Differential Top Feed Foot
96
18 Maintenance
99
18.1 Cleaning
100
18.2 Lubrication
101
18.2.1 Lubricating The Machine Head
102
18.2.2 Lubricating The Looper
103
18.3 Servicing The Pneumatic System
104
18.3.1 Setting The Operating Pressure
104
18.3.2 Draining The Water Condensation
105
18.3.3 Cleaning The Filter Element
106
18.4 Parts List
107
19 Decommissioning
109
20 Disposal
111
21 Troubleshooting
113
21.1 Customer Service
113
21.2 Software Messages
113
21.3 Errors In Sewing Process
118
22 Technical Data
121
23 Appendix
123
Discussie
Laat een opmerking achter of stel een vraag
Doe mee aan de discussie
Stel een vraag over de handleiding of voeg een nuttig antwoord toe voor andere gebruikers.