1. Introduction
3
1.1 Please Read The Manual
3
1.2 Identification Data – Eliet Ultra Prof
3
2.Warranty
3
2.1 Warranty Card
3
3. Welcome
4
4. Table Of Contents
6
5.Safety Symbols
9
5.1 For Your Information
9
5.2 Caution
9
5.3Warning
9
6.Main Parts
10
7.Safety Regulations
13
7.1 Safety Messages
13
7.2 Safety Provisions
17
7.3 Safety Instructions
18
7.3.1 General Safety Instructions
18
7.3.2 Careful And Security-Conscious Use
19
7.3.3 Responsibilities Of The Operator
19
7.3.4 Personal Protective Equipment (Ppe)
20
7.3.5 Danger Zone
20
7.3.6 Periodic Maintenance
21
7.3.7 Limits Of The Machine
21
7.3.8 Preserving Nature
21
8. Dealer Preparation
23
9.Operating Instructions
24
9.1 Preliminary Checks
24
9.2Filling Up With Petrol
25
9.3 Preparing The Work Site
26
9.4 Starting And Stopping The Fuel Engine
26
9.5 Moving The Machine
29
9.6 Operating The Machine
30
9.6.1 Before Starting Work
32
9.6.2 Feed Speed Regulation
33
9.6.3 Abm System
34
9.6.4 Tips For Correct Use
34
9.7 Troubleshooting
36
9.7.1 Engine Failure
36
9.7.2 Engine Losing Power
38
9.7.3 Problem With The Abm System
40
9.7.4 Blockage Of The Discharge System
41
9.7.5 Rotor Stalls
41
9.7.6 Moving The Machine With A Faulty Engine
42
10 Transporting The Machine
43
11.Maintenance
44
11.1 General Provisions
44
11.2 Maintenance Schedules
45
11.2.1 Special Maintenance
45
11.2.2 Regular Maintenance Schedule
46
11.3 Cleaning The Machine
48
11.3.1 The Importance Of Cleaning
48
11.3.2 What Is Cleaning About
49
11.3.3 Cleaning The Cooling System
50
11.4 Engine Maintenance
50
11.4.1.1 Checking The Oil Level
50
11.4.1.2 Topping Up The Oil
51
11.4.2 Engine Oil Change
52
11.4.3 Changing The Oil Filter
52
11.4.4 Cleaning The Air Filter
53
11.4.5 Changing The Air Filter
54
11.4.6 Changing The Fuel Filter
54
11.4.7 Checking And Replacing Spark Plugs
55
11.5 Maintenance Of The Machine
56
11.5.1 Routine Check Of The Blades
56
11.5.2 Sharpening The Blades
57
11.5.3 Reversing And Renewing The Shredding Knives
59
11.5.3.1 To Reverse A Shredding Knife, Proceed As Follows:
59
11.5.3.2 To Replace A Shredding Knife, Proceed As Follows:
62
11.5.4 Adjusting The Drive Belt Tension
63
11.5.5 Tightening The Feed Belt For Correct Tension
65
11.5.6 Tightening The Discharge Belt For Correct Tension
65
11.5.7 Adjusting The Tension Of The Chain Drives
66
11.5.7.1 Checking And Adjusting The Tension Of The Feed Belt Drive Chain
66
11.5.7.2 Checking And Adjusting The Tension Of The Feed Roller Drive Chain
67
11.5.7.3 Checking And Adjusting The Tension Of The Discharge Belt Drive Chain
67
11.5.8 Replacing The Hydraulic Oil And The Oil Filter
68
11.5.9 Replacing The Gas Spring
69
11.5.10 Replacing The Elastic Coupling
69
11.5.11 Checking The Tyres For Correct Pressure
71
11.5.12 Adjusting The Parking Brake
71
11.6 General Lubrication
72
11.6.1 Lubricating The Pivot Points
72
11.6.2 Greasing Via The Grease Zerks Fitted
73
11.6.3 Lubricating The Bearings
73
11.6.4 Lubricating Chains, Sprockets And Gear Wheels
74
12 Winterizing The Machine
75
13 Equipment Specifications
76
14 Ec Declaration Of Conformity
77
Appendix A (Ap.a)
78
P1 Opening Shielding Panels
78
P2 Removing The Discharge Belt Conveyor
79
P3 Opening The Shredding Chamber
80
P4 Raising And Locking The Feed Roller
82
P5 Removing Chain Guards
82
P6 Access To Battery And Wheel Drive Components
83
Appendix B: Procedures
83
Appendix C: Maintenance Schedule
85
Appendix D: Hazard Analysis
86
Appendix E: Meter Display And Functions
87
Appendix F: Warranty Conditions
89
Discussie
Laat een opmerking achter of stel een vraag
Doe mee aan de discussie
Stel een vraag over de handleiding of voeg een nuttig antwoord toe voor andere gebruikers.