Intergas Rapid 32 - 2

Wissel S1 en S2 1. Controleer de kabelstekker. 2. Vervang S1 of S2.

Intergas Rapid 32 - 27

Kortsluiting buitensensor Vervang de buitensensor.

Intergas Rapid 32 - 29

Relaisgas klep defect Vervang de ketelbeheerder.

Intergas Rapid 32 - 30

Relaisgas klep defect Vervang de ketelbeheerder.

Recirculatie van verbrandingsgassen Controleer de gasafvoer en de luchttoevoer.

Gas-/luchtafstelling niet correct ingesteld Controleer de afstelling, zie gas-/luchtafstelling.

Ruimtethermostaat/weerafhankelijke afstelling niet gesloten of defect Controleer de bedrading. Vervang de thermostaat. Vervang de weerafhankelijke afstelling.

Pomp draait niet Controleer de bedrading. Vervang defecte pomp.

Brander brandt niet op CV: sensor S1 of S2 defect Vervang sensor S1 of S2. Zie foutcode.

Bij hoog toerental is het vermogen met meer dan 5% gedaald Controleer het apparaat en het rookkanaal op vervuiling. Reinig het apparaat en het rookkanaal.

Intergas Rapid 32 CV Ketel Handleiding

Q: Intergas Rapid 32 - 0

Sensorfout na zelftest 1. Controleer de bedrading op breuken. 2. Vervang ketelsenor S1 en/of S2.

Q: Intergas Rapid 32 - 0.0

Druksensorfout 1. Zet het verwarmingscircuit onder druk via de vulkraan. 2. Controleer of de druksensor niet verstopt is.

Q: Intergas Rapid 32 - 1

Temperatuur te hoog 1. Controleer of er lucht in het systeem zit. 2. Controleer of de pomp draait. 3. Controleer de circulatie in het systeem; radiators kunnen gesloten zijn of pompinstelling te laag. 4. Controleer of de isolatiekraan niet gesloten is.

Q: Intergas Rapid 32 - 10

Sensorfout S1 1. Controleer of de ketel moet worden ontlucht (handmatige luchtventiel linksboven op de ketel). 2. Controleer de bedrading op breuken. 3. Vervang S1 indien nodig.

Q: Intergas Rapid 32 - 11

Sensorfout S1 1. Controleer of de ketel moet worden ontlucht (handmatige luchtventiel linksboven op de ketel). 2. Controleer de bedrading op breuken. 3. Vervang S1 indien nodig.

Q: Intergas Rapid 32 - 12

Sensorfout S1 1. Controleer of de ketel moet worden ontlucht (handmatige luchtventiel linksboven op de ketel). 2. Controleer de bedrading op breuken. 3. Vervang S1 indien nodig.

Q: Intergas Rapid 32 - 13

Sensorfout S1 1. Controleer of de ketel moet worden ontlucht (handmatige luchtventiel linksboven op de ketel). 2. Controleer de bedrading op breuken. 3. Vervang S1 indien nodig.

Q: Intergas Rapid 32 - 14

Sensorfout S1 1. Controleer of de ketel moet worden ontlucht (handmatige luchtventiel linksboven op de ketel). 2. Controleer de bedrading op breuken. 3. Vervang S1 indien nodig.

Q: Intergas Rapid 32 - 20

Sensorfout S2 1. Controleer de bedrading op breuken. 2. Vervang S2 indien nodig.

No results

1.1 Regulation 5

1.2 Warnings 5

1.3 Manual Handling 5

1.4 Warnings On The Box 5

1.5 Pictograms 5

This Manual 6

1.6 Product Identification 7

2.1 General 8

2.2 The Installation 8

2.3 Approvals 9

3.1 Technical Data 10

3.2 Product Fiche According To Celex-32013R0811, Annex Iv 11

4.1 General Boiler Information 13

4.8 Operation 14

4.9 Operating Modes 14

4.10 Clock Function 16

4.11 Pc Interface 16

4.12 Test Programs 17

4.12.1 Frost Protection 17

5.1 Accessories 19

5.2 Flues 19

6.1 Overall Dimensions 20

6.2 Boiler Location 21

6.2.1 Installation In A Kitchen Cupboard 21

6.2.2 Installation In An Airing Cupboard 21

6.2.3 Remove Front Panel 21

6.3 Assembly 22

6.3.1 Fitting The Mounting Strip 22

6.3.2 Fitting The Spacer Frame 22

6.4 Mount The Appliance 23

7.1 Connect The Ch System 24

7.1.1 Expansion Vessel 25

7.1.2 Thermostatic Radiator Valves 25

7.1.3 Underfloor Heating 25

Appliance With Zone Control 26

7.2 Domestic Hot Water System 27

7.2.1 Appliance With Solar Water Heater Post-Heating 27

7.3 Electrical Connection 28

7.3.1 Electrical Connections 28

7.3.2 On / Off Room Thermostat 29

7.3.3 Open Therm Room Thermostat 29

7.3.4 Outside Temperature Sensor 29

7.3.5 230 Volt Room Thermostat 29

7.3.6 S And Y Zone Plans 29

7.4 Condensate Disposal 30

7.5 Gas Connection 31

7.6 Flue System 32

7.6.1 General 32

7.6.2 Sealed Flue System 32

7.6.3 Flue Pipe And Air Supply 33

7.6.5 Horizontal Flue System 34

7.6.6 Vertical Flue System 34

7.6.7 Plume Management Kit 35

7.6.8 Flues In Voids 35

7.6.9 Free In The Market Availabe Flue Systems (C63) 37

7.6.10 Dimensions Flue Gas Materials: 37

7.6.11 Securing The Flue System 38

8.1.1 Fill And De-Aerate The Appliance And The System 40

8.1.1 Ch System 40

8.1.2 Hot Water Supply 40

8.1.3 Gas Supply 40

8.1.4 Flue System 41

8.2 Commissioning Of The Appliance 42

8.3 Setting And Adjusting The Clock Functions 43

8.3.1 Setting The Clock 43

8.3.2 Setting The Timer Function 43

8.4 Additional Functions 43

8.5 Shutting Down 43

8.5.1 Frost Protection 44

8.6 System Shutdown 44

8.6.1 Frost Protection 44

9.1 Directly Via The Operating Panel 45

9.1.1 Appliance On/Off 45

9.1.2 Dhw Comfort 45

9.1.3 Resetting 45

9.1.4 Changing The Settings Of The Various Functions: 45

9.1.5 Maximum Ch Supply Temperature 45

9.1.6 Dhw Temperature 45

9.2 Settings Through The Service Code 46

9.3 Parameters 46

9.3.1 Enable/Disable Keep Hot Facility By Open Therm Room Thermostat 47

9.4 Setting Maximum Ch Power 48

9.5 Setting Pump Position 48

9.6 Weather-Dependent Control 48

9.7 Conversion To Different Gas Type 49

1.1.1 Converting The Gas Restriction 49

9.8 Gas-Air Ratio Control 50

9.9 Checking The Gas Air Ratio Control 51

9.9.1 Checking Flue Gas At Maximum Power 51

9.9.2 Checking Flue Gas At Minimum Power 52

9.9.3 Correction Gas Air Ratio On Minimum Power 53

10.1 Fault Codes 55

10.2 Other Faults 57

10.2.1 Burner Does Not Ignite 57

10.2.2 Burner Ignites Noisily 57

10.2.3 Burner Resonating 58

10.2.4 No Heating (Ch) 58

10.2.5 The Power Is Reduced 58

10.2.6 Ch Does Not Reach Temperature 58

10.2.7 No Hot Water (Dhw) 59

10.2.8 Hot Water Does Not Reach Temperature 59

10.2.9 Led On Ch Pump Is Flashing Alternately Red And Green 59

10.2.10 Led On Ch Pump Is Flashing Red 59

11.1 Disassembly 60

11.2 Assembly 61

11.3 Combustion 62

11.4 Ntc Resistances 62

11.5 Electrical Diagram 63

Inhoudsopgave

No results

1.1 Regulation 5

1.2 Warnings 5

1.3 Manual Handling 5

1.4 Warnings On The Box 5

1.5 Pictograms 5

This Manual 6

1.6 Product Identification 7

2.1 General 8

2.2 The Installation 8

2.3 Approvals 9

3.1 Technical Data 10

3.2 Product Fiche According To Celex-32013R0811, Annex Iv 11

4.1 General Boiler Information 13

4.8 Operation 14

4.9 Operating Modes 14

4.10 Clock Function 16

4.11 Pc Interface 16

4.12 Test Programs 17

4.12.1 Frost Protection 17

5.1 Accessories 19

5.2 Flues 19

6.1 Overall Dimensions 20

6.2 Boiler Location 21

6.2.1 Installation In A Kitchen Cupboard 21

6.2.2 Installation In An Airing Cupboard 21

6.2.3 Remove Front Panel 21

6.3 Assembly 22

6.3.1 Fitting The Mounting Strip 22

6.3.2 Fitting The Spacer Frame 22

6.4 Mount The Appliance 23

7.1 Connect The Ch System 24

7.1.1 Expansion Vessel 25

7.1.2 Thermostatic Radiator Valves 25

7.1.3 Underfloor Heating 25

Appliance With Zone Control 26

7.2 Domestic Hot Water System 27

7.2.1 Appliance With Solar Water Heater Post-Heating 27

7.3 Electrical Connection 28

7.3.1 Electrical Connections 28

7.3.2 On / Off Room Thermostat 29

7.3.3 Open Therm Room Thermostat 29

7.3.4 Outside Temperature Sensor 29

7.3.5 230 Volt Room Thermostat 29

7.3.6 S And Y Zone Plans 29

7.4 Condensate Disposal 30

7.5 Gas Connection 31

7.6 Flue System 32

7.6.1 General 32

7.6.2 Sealed Flue System 32

7.6.3 Flue Pipe And Air Supply 33

7.6.5 Horizontal Flue System 34

7.6.6 Vertical Flue System 34

7.6.7 Plume Management Kit 35

7.6.8 Flues In Voids 35

7.6.9 Free In The Market Availabe Flue Systems (C63) 37

7.6.10 Dimensions Flue Gas Materials: 37

7.6.11 Securing The Flue System 38

8.1.1 Fill And De-Aerate The Appliance And The System 40

8.1.1 Ch System 40

8.1.2 Hot Water Supply 40

8.1.3 Gas Supply 40

8.1.4 Flue System 41

8.2 Commissioning Of The Appliance 42

8.3 Setting And Adjusting The Clock Functions 43

8.3.1 Setting The Clock 43

8.3.2 Setting The Timer Function 43

8.4 Additional Functions 43

8.5 Shutting Down 43

8.5.1 Frost Protection 44

8.6 System Shutdown 44

8.6.1 Frost Protection 44

9.1 Directly Via The Operating Panel 45

9.1.1 Appliance On/Off 45

9.1.2 Dhw Comfort 45

9.1.3 Resetting 45

9.1.4 Changing The Settings Of The Various Functions: 45

9.1.5 Maximum Ch Supply Temperature 45

9.1.6 Dhw Temperature 45

9.2 Settings Through The Service Code 46

9.3 Parameters 46

9.3.1 Enable/Disable Keep Hot Facility By Open Therm Room Thermostat 47

9.4 Setting Maximum Ch Power 48

9.5 Setting Pump Position 48

9.6 Weather-Dependent Control 48

9.7 Conversion To Different Gas Type 49

1.1.1 Converting The Gas Restriction 49

9.8 Gas-Air Ratio Control 50

9.9 Checking The Gas Air Ratio Control 51

9.9.1 Checking Flue Gas At Maximum Power 51

9.9.2 Checking Flue Gas At Minimum Power 52

9.9.3 Correction Gas Air Ratio On Minimum Power 53

10.1 Fault Codes 55

10.2 Other Faults 57

10.2.1 Burner Does Not Ignite 57

10.2.2 Burner Ignites Noisily 57

10.2.3 Burner Resonating 58

10.2.4 No Heating (Ch) 58

10.2.5 The Power Is Reduced 58

10.2.6 Ch Does Not Reach Temperature 58

10.2.7 No Hot Water (Dhw) 59

10.2.8 Hot Water Does Not Reach Temperature 59

10.2.9 Led On Ch Pump Is Flashing Alternately Red And Green 59

10.2.10 Led On Ch Pump Is Flashing Red 59

11.1 Disassembly 60

11.2 Assembly 61

11.3 Combustion 62

11.4 Ntc Resistances 62

11.5 Electrical Diagram 63

Gebruik de reader hieronder om de Intergas Rapid 32 CV Ketel handleiding te lezen. U kunt de handleidingen direct op de pagina doorbladeren en de functies van onze reader gebruiken om alle belangrijke informatie over de installatie, bediening en het onderhoud van deze Intergas CV Ketel te vinden.

Handleiding

Volledig scherm

Deel deze handleiding Intergas

WhatsApp Email

Was deze handleiding nuttig?

Foutcodes

Hieronder vindt u de error codes voor de Intergas Rapid 32.

0 sensor

KRITIEK

Sensorfout na zelftest

Oplossing

1. Controleer de bedrading op breuken. 2. Vervang ketelsenor S1 en/of S2.

0.0 sensor

KRITIEK

Druksensorfout

Oplossing

1. Zet het verwarmingscircuit onder druk via de vulkraan. 2. Controleer of de druksensor niet verstopt is.

1 temperature

WAARSCHUWING

Temperatuur te hoog

Oplossing

1. Controleer of er lucht in het systeem zit. 2. Controleer of de pomp draait. 3. Controleer de circulatie in het systeem; radiators kunnen gesloten zijn of pompinstelling te laag. 4. Controleer of de isolatiekraan niet gesloten is.

10 sensor

KRITIEK

Sensorfout S1

Oplossing